2nd Generation (GE 08-present)The New Fit... Generation specific talk and questions here.
Welcome to Fit Freak!
Welcome to Fit Freak,
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!
I need to pick up some floor mats for my new Fit and while I was going through the OEM accessories on handaaccessories.com I came across the window visors. I like em, and for 50$ I think Ill just pic them up....
And then I looked at the install directions... GOOD GRIEF...
Its like 5+ pages of instruction, with clip and pulling what looks like weather seals out and little push pins IN the visor it self more brackets etc.
Anyone have these? Is the install as hard as they make it look?
Also with the pins THROUGH the visor, are the little pins very noticable from the outside or inside?
I just wanted clean looking, well fitting visors... did it NEED to be this complicated?
I searched, but either Im searching the wrong term, or there isn't much info on them.
A few pictures from anyone that has them would be apprciated.
__________________
09 Fit Sport MT w/nav: The fun
07 FJ Cruiser: The work horse
Sponsored Links
Registered users do not see this ad. Click here to register for free!
I have installed the Mugen visors on my GD3, and the USDM Honda slim visors on my GE8. It isn't as hard as it looks. My two major pieces of advice on the US Slim Visors--------
There are two clips per visor located at the top, and two more- one at each end. The instructions tell you to temporarily attach the visors with only the top clips, and then to attach the end clips into the door edges and fasten with the little pins. DON'T FOLLOW THAT ADVICE. Attach all clips to each visor with the little pin clips right at the start. With the end clips, rotate them to point down. Then attach the visors with the top clips, pull the tape liners off, and stick them down permanently to the door frames. Then, using needle nose pliers, rotate the end clips so that they fasten to the edge of the window frame.
Attach the metal clips with the plastic pins INDOORS on a table. If you drop those little black clips or little black pins on the ground outside, you'll never find them.
This assumes that you have followed ALL of the other instructions. I have no idea why the little strips of spacer material is needed inside the rubber window seals at two places on the rear windows. But the instructions on where and how to attach the strips are easy to follow, so I did it.
Anyway, it is easier than the instructions make it appear to be. Both the Mugen and Honda Slim Visors reduce wind noise, let you vent the fog out of the car by cracking the windows in the rain, and let you leave the windows cracked in the Summer heat without it being noticeable.
I like the Mugen look on the GD's, and the Honda look on the GE's. Don't let some little details drive you away from a good styling and functional mod.
Im not 100% sure I dig the indent in the Mugen visors.... is there a purpose for that?
The Mugens attach the same way. The indents are for style, not function. Once you get either visor design on the car, they stay put under normal driving and parking conditions. The only possible danger is that anyone can jerk them off the car if their aim is vandalism. Street parking in bad neighborhoods would make these a likely waste of money.
i just installed them 2 weeks ago on my car also.
the instructions make it look harder then it is.
it's really a breeze.
they look good and function great.
I just installed mine today. I must agree with the others, its really easy to do. Just follow the instructions and pay close attention to what brackets what and you'll be good. For the price its a good deal compared to auto vent shade products. Better quality overall!
Im not 100% sure I dig the indent in the Mugen visors.... is there a purpose for that?
I forgot your question on the Mugen cost. I bought the set for my GD from King Motorsports about 1 1/2 years ago for about $170.00 and was not disappointed in the cost or quality. That was the average price all over the Internet at that time. I have no idea what the Mugen price is for GE's, but the Honda Slim Visors are much less expensive (less than half) through College Hills Honda, and various eBay vendors.
Yeah, I really can't complain too much about my dealer... good guys.
Window visors on... and mats in. Although it was a slight pain to cut the rubber and carpet (woulda been ALOT better in the daylight) the drivers side mat holders are a NICE design...
She already looks a bit better... windows being tinted on the 13th...
__________________
09 Fit Sport MT w/nav: The fun
07 FJ Cruiser: The work horse
korywithak, thats funny! I did the same thing with my lap top. I had the pdf up because I ran out of ink in my printer. I live in the northeast and I'm waiting till it gets a little warmer to get some tint as well. congrats on the window visors.
As you can see, the black pins are barely visible.
I didn't put all of the foam in the weather stripping. The lower back window molding is a pain to pull out and pretty fragile.
I didn't notice any increase in noise.
__________________
2009 Fit Sport MT
40-50+ mpg
40,000 miles
- you can open your windows a little bit while it is raining/snowing, etc which is nice when parking the car on a day that might get rain, if you are a smoker, or if you just need to vent the cabin
- blocks a small amount of sunlight (very nice on my morning drive)
- some find them aesthetically pleasing
__________________
2009 Fit Sport MT
40-50+ mpg
40,000 miles
for me it even eliminated that thunder noise you get
when you only crack the back windows only. it used to
practically shack the front doors. now nothing.
Linear Mode
