Baylorbro's Photo Thread
#1
Baylorbro's Photo Thread
***Update on page 3***
So to start off my photo thread, I'm going to start simple with a classic badge switch and then rock your world with what might be the first GE with NOS! lol Here it goes...
Badge switch! Loving the red dot (which bigtoepfer tells me comes from the jazz 1.3L, I think)
This exoctic and rarely seen-on-a-fit system is a nitrous kit. I was very lucky when putting in this kit. The heat shield for my intake is about the only place I could easily mount the management unit. The braided lines going into the unit in the front are fuel and nitrous in, while fuel and nitrous out mix come out the back, wrap around top of the intake pipe and are tapped into the intake.
Notha angle, good shot of the spray nozzle and fuel supply to nitrous/fuel mixture.
From the top
Nice shot of the management unit mount.
Yes, those are zip ties, and yes they will be replaced with something more durable and not as "rigged". Also need to get a rubber fitting to go around the lines to keep them from vibrating at points of contact with other metal pieces.
Bottle, mounted, check. Connection line comes from spare wheel compartment, I leave the bottle disconnected while daily driving.
Hope you enjoyed. Put it in with a buddy of mine, all by ourselves. I'd say total time over the span of a few days took about 8 hours. Neither of us have done an install like this before though, so I was proud of our work. Something nice to know for GE owners, YOU CAN CHANCE SPARK PLUGS WITHOUT REMOVING ANY OF THE ASSEMBLY AT THE BASE OF THE WINSHIELD. Just need to know what you are doing so you can work blind, also helps if you have long arms. I changed out my stock plugs for the Zex cold plugs, a must if running nitrous.
If you have any questions about the install LMK!
I expect the Fast and Furious jabs. Actually, really I'd be disappointed if they didn't come, so bring it!
So to start off my photo thread, I'm going to start simple with a classic badge switch and then rock your world with what might be the first GE with NOS! lol Here it goes...
Badge switch! Loving the red dot (which bigtoepfer tells me comes from the jazz 1.3L, I think)
This exoctic and rarely seen-on-a-fit system is a nitrous kit. I was very lucky when putting in this kit. The heat shield for my intake is about the only place I could easily mount the management unit. The braided lines going into the unit in the front are fuel and nitrous in, while fuel and nitrous out mix come out the back, wrap around top of the intake pipe and are tapped into the intake.
Notha angle, good shot of the spray nozzle and fuel supply to nitrous/fuel mixture.
From the top
Nice shot of the management unit mount.
Yes, those are zip ties, and yes they will be replaced with something more durable and not as "rigged". Also need to get a rubber fitting to go around the lines to keep them from vibrating at points of contact with other metal pieces.
Bottle, mounted, check. Connection line comes from spare wheel compartment, I leave the bottle disconnected while daily driving.
Hope you enjoyed. Put it in with a buddy of mine, all by ourselves. I'd say total time over the span of a few days took about 8 hours. Neither of us have done an install like this before though, so I was proud of our work. Something nice to know for GE owners, YOU CAN CHANCE SPARK PLUGS WITHOUT REMOVING ANY OF THE ASSEMBLY AT THE BASE OF THE WINSHIELD. Just need to know what you are doing so you can work blind, also helps if you have long arms. I changed out my stock plugs for the Zex cold plugs, a must if running nitrous.
If you have any questions about the install LMK!
I expect the Fast and Furious jabs. Actually, really I'd be disappointed if they didn't come, so bring it!
Last edited by thefit09; 08-04-2010 at 09:50 PM.
#5
Just ran it with the 45hp jet, damn. Just damn.
#6
Fit looks good you just need to clean up those lines.. are you going to get it dyno'd?
The fit can only handle so much.. s/c+nitrous=boooom
The fit can only handle so much.. s/c+nitrous=boooom
#9
The shop I got the bottle filled at does dyno's... anyone know how much I should be willing to pay?
Also, what should I do with the lines (other than replacing the zip ties). I'm really not sure what to do with the extra length. Any ideas?
Also, what should I do with the lines (other than replacing the zip ties). I'm really not sure what to do with the extra length. Any ideas?
#12
Treatin me well, other than the fact that a couple of the jets I was sent were wrong... but Zex fixed it and is sending me some new ones.
#15
I will be watching out for your car when I am in Waco next month for a medical appointment.... There is a little yellow Suzuki Swift in that area that has to be boosted that left me like I was in reverse when my car was stock.... Kick his ass for me if you are ever side by side with him on 35.