What did you do to your GK Fit today?
#2065
.... thanx in advance!!
#2066
75700-S5T-E11
75700-S5T-E01
the front ones pins line up, but the rear you will have to remove the pins from the new emblem to install
#2067
Hypergram Fitment
not good. The offset made me have to roll the rears but I was using a pretty fat 205 maxxis tire. Also im lowered a good bit. The fronts struck out a lot too but only rubbed while racing.
#2068
7.5j offset 35?
#2069
Hypergrams
https://www.good-win-racing.com/Mazda-Performance-Part/61-1922.html
yes, 35 mm offset. Which pushes them out 18mm, plus they are 1.5" wider than stock so another 3/4" further out. Basically 1.5" out. Before camber bolts up front, they really stuck out. In the rears I had to cut the felt (EX) and roll the fenders. I also put the front fender liners above the fender tabs. It still rubs on high g corners up front. I need to roll the fenders up front.
yes, 35 mm offset. Which pushes them out 18mm, plus they are 1.5" wider than stock so another 3/4" further out. Basically 1.5" out. Before camber bolts up front, they really stuck out. In the rears I had to cut the felt (EX) and roll the fenders. I also put the front fender liners above the fender tabs. It still rubs on high g corners up front. I need to roll the fenders up front.
#2071
Put the SSR Type X's on after a fresh powder coat job with fresh Dunlop rubber (205/50/15). Used some Project Kics Bronze Lugs and matching valve stem caps. New Project Kics Valve Stems. Also lowered the car with H&R Springs from the GE8. No pictures of this but also installed the Spoon Sports Rearview mirror (do this mod. it so worth it).
#2072
Put the SSR Type X's on after a fresh powder coat job with fresh Dunlop rubber (205/50/15). Used some Project Kics Bronze Lugs and matching valve stem caps. New Project Kics Valve Stems. Also lowered the car with H&R Springs from the GE8. No pictures of this but also installed the Spoon Sports Rearview mirror (do this mod. it so worth it).
#2074
Actually the suspension has changed: the struts have different bump stops, and rear shocks have a longer rod and significantly different configuration of urethane bump stop and bushing that mates with the chassis. The mounting point for the rear shock in the GK is higher in the chassis, so the rod for the shock is longer to allow for the same drop and effective working length of the shock. The GE8 parts fit the GK, however I would think that the rear of the car would need to be lowered for the GE shocks to allow for the same travel of the shock and the rear end (i.e. drop). The stock springs are the same dimensions, not sure if the rate changed at all as I didn't have the means to measure them.
TL;DR the struts are essentially the same, the rear shocks for the GK can't be used on the GE8, but the opposite can work.
TL;DR the struts are essentially the same, the rear shocks for the GK can't be used on the GE8, but the opposite can work.
Last edited by Alfa38; 12-03-2018 at 10:36 PM.
#2075
Actually the suspension has changed: the struts have different bump stops, and rear shocks have a longer rod and significantly different configuration of urethane bump stop and bushing that mates with the chassis. The mounting point for the rear shock in the GK is higher in the chassis, so the rod for the shock is longer to allow for the same drop and effective working length of the shock. The GE8 parts fit the GK, however I would think that the rear of the car would need to be lowered for the GE shocks to allow for the same travel of the shock and the rear end (i.e. drop). The stock springs are the same dimensions, not sure if the rate changed at all as I didn't have the means to measure them.
that would probably be my main concern. The spring rates. As far as bump stops, if you have some solid coilovers and cut the stops accordingly then when are you actually gonna hit the bump stop while driving normally
#2077
Put the SSR Type X's on after a fresh powder coat job with fresh Dunlop rubber (205/50/15). Used some Project Kics Bronze Lugs and matching valve stem caps. New Project Kics Valve Stems. Also lowered the car with H&R Springs from the GE8. No pictures of this but also installed the Spoon Sports Rearview mirror (do this mod. it so worth it).