I'd have definitely gone with more camber.
But the TE do look nice. |
Awesome thread! Your car looks great!
Have any SRS issues switching to the low max seat? |
Originally Posted by Aznsupastar
(Post 1391008)
still waiting 4 pix pls :vtec:
|
Originally Posted by CodemanGK5
(Post 1391081)
Awesome thread! Your car looks great!
Have any SRS issues switching to the low max seat? A fellow member USDS, has this explained in his build thread with pics! Are you swapping in a new seat soon? |
VOLKS! So jealous! How has changing to VOLKS affected acceleration/braking?
|
Originally Posted by 2Rismo2
(Post 1391101)
VOLKS! So jealous! How has changing to VOLKS affected acceleration/braking?
I just got my 65mm to 56.1mm center hub rings and plan to throw those on as well this weekend. I still cant get off of my mind the gap that exists between the center bore of my TEs to the wheel hubs.. Even after the alignment, I am not sure if I am imagining that the car vibrates at Highway speeds due to the absence of the centric hub rings, but I want those on immediately for peace of mind..mind you I had centric hub rings on my last wheel setup, no vibrations then. |
Originally Posted by CodemanGK5
(Post 1391081)
Have any SRS issues switching to the low max seat?
https://www.fitfreak.net/forums/2nd-...ll-begins.html https://www.fitfreak.net/forums/3rd-...ml#post1383703
Originally Posted by TougeMonster_GK5
(Post 1391096)
I did run into the SRS issues, but that was quickly resolved after installing a 2.2OHM resistor from vetco.net.
A fellow member USDM, has this explained in his build thread with pics! |
Installed the 65mm to 56.1mm centric hub rings
https://cimg0.ibsrv.net/gimg/www.fit...8a1712fcf2.jpg https://cimg5.ibsrv.net/gimg/www.fit...b3f2825bc1.jpg For the kind gentlemen that requested detailed pix of my fender rolled: https://cimg1.ibsrv.net/gimg/www.fit...a0c29295b7.jpg https://cimg2.ibsrv.net/gimg/www.fit...9230e3697d.jpg https://cimg6.ibsrv.net/gimg/www.fit...deffeba467.jpg |
no more rubbing?
|
Originally Posted by kenchan
(Post 1391204)
no more rubbing?
|
lol, your car passed the big boy validation test. :D
|
Car looks great, lots of good info in this thread too!
Just curious if you ran into any issues with the RS spoiler? Did you install yourself or have it done by a shop? |
Originally Posted by ThadCastle
(Post 1391227)
Car looks great, lots of good info in this thread too!
Just curious if you ran into any issues with the RS spoiler? Did you install yourself or have it done by a shop? |
touge - moar picts pls!!!
|
thx 4 showing me those beautiful rolled fender pix! as predicted, the fit barely has much "lip" to roll in stock form. but additional clearance is always welcome!
wait..so if u get the RS wing, u have to lose your rear washer spray?! |
Originally Posted by kenchan
(Post 1391271)
touge - moar picts pls!!!
|
Originally Posted by Aznsupastar
(Post 1391302)
thx 4 showing me those beautiful rolled fender pix! as predicted, the fit barely has much "lip" to roll in stock form. but additional clearance is always welcome!
wait..so if u get the RS wing, u have to lose your rear washer spray?! The REP RS Wing I purchased on Aliexpress doesn't have an opening in order for me to use the stock rear washer spray. I could have drilled/cut-out an area for it, but didn't want to take a chance on it, I waited over a month for it to get here and just wanted it on. The other REPS available (via Ebay, Amazon) require professional body work to get bolted on. I would have gone real JDM, but that requires the entire JDM Hatch... |
Originally Posted by TougeMonster_GK5
(Post 1391305)
You are most welcome! If you noticed in the pics, the guy who rolled my fenders also cuts portions of the inner well plastic shroud.
The REP RS Wing I purchased on Aliexpress doesn't have an opening in order for me to use the stock rear washer spray. I could have drilled/cut-out an area for it, but didn't want to take a chance on it, I waited over a month for it to get here and just wanted it on. The other REPS available (via Ebay, Amazon) require professional body work to get bolted on. I would have gone real JDM, but that requires the entire JDM Hatch... |
Originally Posted by Aznsupastar
(Post 1391318)
How much does it go for on aliexpress? Comes painted? Can u show me that hole u talking about on the wing? Thx
https://www.aliexpress.com/snapshot/...Id=32801475239 |
Do you have another link for the wing by chance? All the ones on AliExpress look the same, and same as the ones on eBay. Really interested if it just bolts on! Although I do use my rear wiper spray occasionally.
Really wish the aftermarket would get USDM friendly already! |
All times are GMT -4. The time now is 02:47 AM. |
© 2024 MH Sub I, LLC dba Internet Brands