Installed T1R Header and Test Pipe
I finished installation of my T1R header and test pipe the other day. But the header gasket was leaking so I swapped the header back out with the stock exhaust manifold temporarily until I get a new donut gasket that will fit.
Just thought I would show off a few pics. http://i47.tinypic.com/m9y360.jpg http://i49.tinypic.com/122c6qc.jpg http://i47.tinypic.com/ekkifb.jpg http://i54.tinypic.com/akcoky.jpg http://i50.tinypic.com/21jrts4.jpg http://i49.tinypic.com/14cb4mx.jpg |
Good stuff
I'm use to exhaust systems,headers etc on big ol domestics like the Mustang :) I'll most likely keep my Fit exhaust stock but it's good to see what mods are available and how they perform. I see the primary cat is deleted with the test pipe.Does the T1R header have larger primaries then the stock manifold? Be sure to post up a sound clip when you get that gasket :) |
Originally Posted by zilla8
(Post 1122179)
Good stuff
I'm use to exhaust systems,headers etc on big ol domestics like the Mustang :) I'll most likely keep my Fit exhaust stock but it's good to see what mods are available and how they perform. I see the primary cat is deleted with the test pipe.Does the T1R header have larger primaries then the stock manifold? Be sure to post up a sound clip when you get that gasket :) As for videos, I will record two sound clips as soon as I can. (1) Stock Exhaust Manifold + T1R Test Pipe + Skunk2 Cat-Back (2) T1R Header + T1R Test Pipe + Skunk2 Cat-Back I just have to find the right time to record them since I live in an apartment complex and have no driver's license. As loud as it is I might get a few complaints, but it will be totally worth it :cool: |
I hear ya on not wanting to cause a ruckus with the neighbors lol
you don't need them calling the cops on you thats for sure. I like the looks of the T1R header and agree the diameter looks pretty close to stock but the collector and overall apearence is superior. |
The donut gasket came in the mail today so I fitted it up to the header and it is a perfect fit.
Therefore, I would recommend to anyone who purchases the T1R header used like I have done to purchase the the following gasket: Vibrant Performance: #10532 (2.03" I.D. X 0.55") http://i48.tinypic.com/16oq55.jpg http://i46.tinypic.com/1zxr5sw.jpg http://i46.tinypic.com/2vrwso2.jpg http://i47.tinypic.com/2m29sud.jpg http://i47.tinypic.com/w1dan9.jpg http://i46.tinypic.com/2hd18yh.jpg |
Originally Posted by icollins247
(Post 1122702)
The donut gasket came in the mail today so I fitted it up to the header and it is a perfect fit.
|
Originally Posted by doctordoom
(Post 1122737)
It doesn't look like it's seated flush?
|
did you ever get the sound clips?
|
Originally Posted by mangosmoody
(Post 1338376)
did you ever get the sound clips?
|
Id love to see a stepped, 4-2-1 header for one of these. I bet it would pull the torque WAY up..
|
Originally Posted by dwtaylorpdx
(Post 1338607)
Id love to see a stepped, 4-2-1 header for one of these. I bet it would pull the torque WAY up..
|
The Nascar guys use them over the old long tubes, they are still turning > 9K so it doesn't seem to hurt the upper end much :D
|
All times are GMT -4. The time now is 08:14 AM. |
© 2024 MH Sub I, LLC dba Internet Brands