Pandahh's custom sub set-up.
 

This isn't a DIY, it's just to show what I made with my dad :)

We built a custom sub set-up in the spare tire housing (spare tire removed, though), anddd there's plexiglass, so you can see through!

Attachment 35244

The housing for the sub is an 11" diameter plastic bucket with the bottom of it cut to fit the contours of the floor under the spare tire (if you lift the spare, you'll see that it's not a flat surface, which made things a little more difficult) then, around the plastic bucket is some wood pieces, to add strength to the housing, they're also custom cut on the bottoms to fit the contours. here's some pics so you know what I'm talking about:

Attachment 35245
That's the wood pieces, in a straight line, with the uncut plastic bucket. The wood has tape over it, so it stays together, but is still flexible.

Attachment 35246
That's the plexiglass, with the protective sheet still on it. My dad cut off the lid that's covering the spare tire on the floor of the trunk, and used it as a template to cut the plexiglass. Then, he measured a hole, about 12", in the center of the glass, where the sub goes.

Attachment 35247
Then, I wrapped the wood pieces around the bucket, and drew a line on the bucket with sharpie to mark the angles of the wood pieces, then I took the wood off and I cut along the line on the bucket with an exacto knife.

Attachment 35248
Then, the bucket looked like this, and I placed a strip of weatherstripping around it, so that the wood wouldn't vibrate up against the bucket while the bass is bumpin'.


Attachment 35249
Here's the bucket with the wood around it (it's held together with 48" zip ties). Then, I got a sheet of felt, and cut individual pieces to fit on each piece of wood. this is so that the housing isn't vibrating against the metal trunk floor.

Attachment 35250
I spray painted the sub housing matte black, since it's going to be visible through the plexiglass.

Attachment 35251

Attachment 35252
Then, I cleared out the trunk and taped plastic sheets around the entire area to prepare for spray painting the spare tire well.

Attachment 35253
I picked this color because it matches so well with my rims :D

Attachment 35254
Painteddd

Attachment 35255
Attachment 35256
everything put in place, aaaand done!!

oh and some LEDs, just for fun... ;)
Attachment 35257

that is freakin awesome!! =o

rep+

edit: i was looking at the last pic and i realize there's room to put some things there to show off as well. Being a sneakerhead, some nice kicks can go right in there lol

Look pretty good. Did you sealed the bucket against the floor so there wouldn't be air leak? Is that adequate air volume for the sub? Bucket look pretty small after cutting to fit the floor. Most important, how it sound?
Nice to see your dad helping you out on the fit instead of saying no.

THAT WOULD BE bad ass HEATHER, YOU SHOULD PUT YOUR NEW PINK AND ORANGE NIKES IN THERE!

hella custom!!

Very nicely done! How does it sound?

Looks to be a shallow mount sub so that should be plenty for a sealed box.

Great install by the way Pandahh! Looks very nice :wavey:

Daaaang. Very nice! Just gave me some ideas of my own...

thank youuu :) haha I think I'll just keep it simple and not fill up the space :s

yeah, it's sealed with silicone gel

It sounds decent. I mean, I don't get as hard of hits as I did with the full box that I had before, but I'm also still working on adjusting the set-up, so there's room for improvement. I think I'm going to switch from the Kicker sub that I have now to a JL sub. I also need to add dynamat to the floor. If those two don't improve the sound, Imma have to redo the whole box. this time with MDF wood.

haha they're not new anymore! they're all dirty and stuff!!!

thank you, thank youu :)

this is the greatest thing i ever seen in my life! i wish you lived close to me so i could have this done!

I noticed your setup at the meet last time, but I didn't really get a chance to look at it. Will you be there tomorrow? I want to see this in person.

ahhh it's not set up like this anymore :/ I found that compared to other sub set ups in my friend's cars, mine didn't sound so great because of the small volume. I put the sub back into a regular box and was going to cut the plexi glass to fit around the box, but it turns out I'll need a new sheet of glass for that. it's a trial and error process I guess haha. hopefully I'll have it looking pretty again soon!

oh and I won't be at tomorrow's meet but I'll be there next week... and hopefully lowered by then ;)