Unofficial Honda FIT Forums - Search Results

 
Search: Posts Made By: leonine
Showing results 1 to 25 of 488
Search took 0.18 seconds.
Replies: 105
Views: 14,648
Posted By leonine

Yup 93 octane

Yup 93 octane
Replies: 105
Views: 14,648
Posted By leonine

Found this on the replacement sent from...

Found this on the replacement sent from Kraftwerks.
Replies: 105
Views: 14,648
Posted By leonine

Numbers

268whp
200wtq
16psi
belt is slipping so I had to get a new tensioner from Kraftwerks.
Replies: 187
Views: 21,297
Posted By leonine

yes stock fuel pump is fine on 10psi. I would...

yes stock fuel pump is fine on 10psi. I would suspect it can handle up to 200hp.
Replies: 105
Views: 14,648
Posted By leonine

Yup!!! Tomorrow it's going on. Running fine now...

Yup!!! Tomorrow it's going on. Running fine now front blower was replaced cause it was leaking.

hoping for some great numbers :)
Replies: 105
Views: 14,648
Posted By leonine

No good pics of the TB yet. It is directly under...

No good pics of the TB yet. It is directly under the manifold. The oem fam and shroud was removed and replaced with a higher output one.

the wires needed to be extended to the throttle body but...
Replies: 105
Views: 14,648
Posted By leonine

Some more engine shots now that it is fully...

Some more engine shots now that it is fully assembled.https://cimg5.ibsrv.net/gimg/www.fitfreak.net-vbulletin/1240x2000/80-collage_2017_02_22_06_42_11_2b0c7e41b8e20fc5d8d9633d9ae6f006e00bd21d.jpg...
Replies: 105
Views: 14,648
Posted By leonine

correctamundo :)

correctamundo :)
Replies: 105
Views: 14,648
Posted By leonine

I'm sure they wish they were out racing. As far...

I'm sure they wish they were out racing. As far as I know they are trying to get my car finished as it has been taking up a bay for a year now. Your best bet is to message them through Facebook.
...
Replies: 105
Views: 14,648
Posted By leonine

It is done and ready to order. Contact Greg and...

It is done and ready to order. Contact Greg and let him know Brian sent you.
Replies: 187
Views: 21,297
Posted By leonine

nice build! Looking forward to seeing the...

nice build! Looking forward to seeing the manifold complete. And that J swap is freakin awesome!!!
Replies: 187
Views: 21,297
Posted By leonine

I ran both. Flashpro was not available at the...

I ran both. Flashpro was not available at the time so I was using the AEM F/IC
Replies: 187
Views: 21,297
Posted By leonine

yeah the transmission held up nicely never had...

yeah the transmission held up nicely never had any problems. I ran a transmission cooler and drained/refilled (around 2 qts if I recall give or take) every 10-12k.

I never ran an intercooler so...
Replies: 1
Views: 638
Posted By leonine

J's Racing front lip for the gd3

Pics if you have one for sale I am interested. Thanks.
Replies: 187
Views: 21,297
Posted By leonine

That's great! What is the pulley diameter you are...

That's great! What is the pulley diameter you are running now. I never got a measurement of the diameter on the high boost pulley.
Replies: 187
Views: 21,297
Posted By leonine

Honda fluid the whole time

Honda fluid the whole time
Replies: 187
Views: 21,297
Posted By leonine

I am running 2 rotrex c15-60 units. Check...

I am running 2 rotrex c15-60 units.

Check out my build thread on this site. GD3 Rotrex Build.

You can contact my builder his info is on that thread. Brackets, billet parts, head gasket, cat...
Replies: 187
Views: 21,297
Posted By leonine

Not one single transmission problem. Run a tranny...

Not one single transmission problem. Run a tranny cooler and change the fluid (drain and refill not flush) every 10-12k
Replies: 187
Views: 21,297
Posted By leonine

Thanks for asking. The A/T lived a long happy...

Thanks for asking. The A/T lived a long happy life until 200k. Ran 10 psi most of the time. Wound up having electrical problems that could not be found and fixed. Could have been from water damage in...
Replies: 105
Views: 14,648
Posted By leonine

Thanks. The 15-60 is rated at close to 240hp on...

Thanks. The 15-60 is rated at close to 240hp on the rotrex tech sheet. Pulleys are the same as the original kit. I am using 2 blowers so I am hoping to be in the 280-320hp range.

But whatever the...
11-03-2016, 09:19 PM
Replies: 0
Views: 767
Posted By leonine

GD3 adjustable cam gear

Wanted to let anyone who is interested that the gd3 l15a1 now has an adjustable cam gear! This was custom made for my build and the designer is making them available to the public.

Pre order is...
Replies: 105
Views: 14,648
Posted By leonine

They are close to being done and will put up...

They are close to being done and will put up order info on their site.
Replies: 105
Views: 14,648
Posted By leonine

They cut it from a 75lb block of T6061 aluminum....

They cut it from a 75lb block of T6061 aluminum. Made it in plastic first to check for fitment with their mockup motor in my car.

Working on the valve cover now...
Replies: 105
Views: 14,648
Posted By leonine

Manifold is done

Manifold is done
Replies: 105
Views: 14,648
Posted By leonine

They already know that people are interested. But...

They already know that people are interested. But it will not be cheap. People need to call them and express interest.
Showing results 1 to 25 of 488
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.