My Seat Belt Webbing replace to Porsche Yellow Color
Here are the DIY to replace Seat Belt Webbing.
I sent my OEM Honda Factory Seat Belt to "SAFETY RESTORE" https://www.safetyrestore.com Both Mike Mason and Rusty at Safety Restore were always very responsive to my inquiry via email or text message. I asked them to send me pictures of the Porsche Yellow color so I can see the color and texture of the webbing and they send it right away. They also manage to do 1 day turn around meaning my seat belt was done in the same day it arrived at their facility. They currently had promotion going on since they just move to new address for 15% of the entire total/order plus free return shipping using USPS Priority mail ! I really recommend their service, their price is much cheaper than the other vendor that can do this webbing changes. Ok here are the DIY: I forgot to take many pictures when I took off the seat belt, but I took detailed steps by steps picture when I install the now Porsche Yellow seat belts :D, so just use it as reference (in reverse step) to take out the OEM Honda seat belt. Ok First, make sure you disconnect the Negative terminal of your battery before you start and wait 3 minutes for the entire system to discharge, this will prevent accidental airbag deployment. All Seat Belts came in USPS Priority Mail and packed well: https://cimg1.ibsrv.net/gimg/www.fit...d97e909fc8.jpg https://cimg2.ibsrv.net/gimg/www.fit...7739a4de52.jpg All original label from the OEM Honda seat belt were reattached to the new Yellow Webbing: https://cimg3.ibsrv.net/gimg/www.fit...51892915c1.jpg Apply Loctite Medium Strength (BLUE) install the LOWER Big Bolt that hold the Front Seat Belt housing unit https://cimg5.ibsrv.net/gimg/www.fit...50dd02cae4.jpg https://cimg6.ibsrv.net/gimg/www.fit...8e97ebf93b.jpg and tighten it to 32nm with torque wrench https://cimg0.ibsrv.net/gimg/www.fit...30adedb279.jpg https://cimg3.ibsrv.net/gimg/www.fit...81c6163291.jpg https://cimg8.ibsrv.net/gimg/www.fit...79e3c86c48.jpg then install the smaller bolt on the top part of the seat belt unit and tighten it to 4nm with torque wrench: https://cimg2.ibsrv.net/gimg/www.fit...9af711be3e.jpg Reconnect the SRS wiring (yellow socket): https://cimg6.ibsrv.net/gimg/www.fit...956664e8a9.jpg https://cimg5.ibsrv.net/gimg/www.fit...cb47db1ffd.jpg Now install the Height Adjustment Attachment, again using Loctite and 32nm torque wrench: https://cimg7.ibsrv.net/gimg/www.fit...f2625802bd.jpg https://cimg8.ibsrv.net/gimg/www.fit...ab3f5c2c4e.jpg https://cimg9.ibsrv.net/gimg/www.fit...69aae65137.jpg https://cimg0.ibsrv.net/gimg/www.fit...b655a91565.jpg https://cimg1.ibsrv.net/gimg/www.fit...c5b593952d.jpg Then you need to install the black lower B pillar plastic interior panel first: https://cimg3.ibsrv.net/gimg/www.fit...40629b1a2a.jpg Finally you can install the lower final anchor bolt, as usual Loctite Blue and 32nm Torque also notice the arrangement of the washer/spacer on the botl: https://cimg2.ibsrv.net/gimg/www.fit...2ea96ec6c8.jpg https://cimg4.ibsrv.net/gimg/www.fit...70a8451479.jpg https://cimg5.ibsrv.net/gimg/www.fit...ead7980d55.jpg https://cimg7.ibsrv.net/gimg/www.fit...b48bbbdb54.jpg https://cimg8.ibsrv.net/gimg/www.fit...b3f26ae942.jpg https://cimg9.ibsrv.net/gimg/www.fit...a47b6a645c.jpg Front Seat Belt Done, The different for the passenger side is the lower anchor bolt is bolted to the right side of the passenger seat: https://cimg1.ibsrv.net/gimg/www.fit...810267f2e4.jpg |
Now for rear seat belt:
You need to slightly open the side rear plastic panel (that lined both side of the trunk wall) to access the mounting for the rear seat belt. Than just like the front seat belt, you need to use Loctite and tighten to 32nm for larger anchor bolt (size 14mm on the socket wrench), and just 4nm torque on the smaller size bolt (size 10mm on the socket wrench) Here are the pictures that should be self explanatory: https://cimg4.ibsrv.net/gimg/www.fit...8da9438b1e.jpg https://cimg5.ibsrv.net/gimg/www.fit...5f7697672f.jpg https://cimg8.ibsrv.net/gimg/www.fit...9beee9db79.jpg This is the TOP anchor (to the ceiling), notice the spacer position on the bolt: https://cimg6.ibsrv.net/gimg/www.fit...807a854380.jpg https://cimg0.ibsrv.net/gimg/www.fit...ee44f84627.jpghttps://cimg1.ibsrv.net/gimg/www.fit...f5cc9e86d9.jpghttps://cimg2.ibsrv.net/gimg/www.fit...ccd5e57eda.jpghttps://cimg3.ibsrv.net/gimg/www.fit...d156857f33.jpg |
For Finishing Touch, I decide to install the RECARO Seat Belts Pads that I bought long time ago (like more than 1 year ago),
this are real JDM Recaro products, that I originally want to install after I buy the Recaro SR-7 ASM Limited Ruby Seats, but... I decide to install it now since this will motivate me to find the funds to buy the Recaro SR-7 ASM Limited Ruby :vtec: https://cimg6.ibsrv.net/gimg/www.fit...e069e12096.jpghttps://cimg7.ibsrv.net/gimg/www.fit...4ece0d3f6f.jpghttps://cimg8.ibsrv.net/gimg/www.fit...4d9ef5ff47.jpghttps://cimg9.ibsrv.net/gimg/www.fit...e8ef952351.jpghttps://cimg0.ibsrv.net/gimg/www.fit...fdd58f6292.jpg |
I forgot to mention the last step,
if you disconnect the SRS wiring from the front seat belt unit, and you turn on the car (reconnect the battery), it will trigger and error code that can only be erase either going to the dealer or using HIM Diagnostic tool. I use HIM Diagnostic tool to erase this error code. I bought it long time ago on eBay: https://www.ebay.com/sch/i.html?_fro...ostic&_sacat=0 but if you don't want to do this, then you can't reconnect the battery until you install the seat belt back. |
Upload the DIY to YouTube :)
|
Looks great!
|
Originally Posted by USDM
(Post 1380399)
Looks great!
|
All times are GMT -4. The time now is 10:42 PM. |
© 2024 MH Sub I, LLC dba Internet Brands