Jazz/Fit from downunder *new member*
Thread Starter
|
New Member
Joined: Dec 2010
Posts: 2
From: Sydney, Australia
Jazz/Fit from downunder *new member*
Hey guys, my names Alex and have just joined this site. Im from Sydney, Australia and am looking at getting some extra info on my Jazz/Fit...
My car is a 2007 Honda Jazz Vti-S (5 speed manual) and is the top of the range model that was released in here, i bought the car with some of the mods already done but have added a few mods of my own to get it to how it sits today...
heres a list as to whats done to it:
Buddy club n+ coilovers
Japanese muffler (JASMA plated)
Cusco front lower tie bar
Spoon front strut brace
Spoon reservoir covers
Spoon engine damper
Spoon throttle body
Buddy club oil cap
Buddy club radiator cap
Toda intake with k&n filter
J racing grille
J racing front air duct
J racing roll centre adjusters
Nardi 350mm deep corn wheel
Splash boss kit
Spoon duracon gearknob
Mugen short shifter
Mugen visors
Mugen number plate bolts
Spoon (genuine) carbon fibre wing
J racing c pillar brace
J racing b pillar floor brace
Mugen tailgate finisher
DIY Auxiliary cable (for ipod connection)
Short stubby erricsson antenna
35% tints on front and 20% tints on rear
16x7 Enkei Jspeed 3's, +35 offset
and of course some pics...
I would like some information on relocating the rear bumper tabs, i did a quick search and didnt find anything... can anyone help point me in the right direction?
Cheers, Alex.
My car is a 2007 Honda Jazz Vti-S (5 speed manual) and is the top of the range model that was released in here, i bought the car with some of the mods already done but have added a few mods of my own to get it to how it sits today...
heres a list as to whats done to it:
Buddy club n+ coilovers
Japanese muffler (JASMA plated)
Cusco front lower tie bar
Spoon front strut brace
Spoon reservoir covers
Spoon engine damper
Spoon throttle body
Buddy club oil cap
Buddy club radiator cap
Toda intake with k&n filter
J racing grille
J racing front air duct
J racing roll centre adjusters
Nardi 350mm deep corn wheel
Splash boss kit
Spoon duracon gearknob
Mugen short shifter
Mugen visors
Mugen number plate bolts
Spoon (genuine) carbon fibre wing
J racing c pillar brace
J racing b pillar floor brace
Mugen tailgate finisher
DIY Auxiliary cable (for ipod connection)
Short stubby erricsson antenna
35% tints on front and 20% tints on rear
16x7 Enkei Jspeed 3's, +35 offset
and of course some pics...
I would like some information on relocating the rear bumper tabs, i did a quick search and didnt find anything... can anyone help point me in the right direction?
Cheers, Alex.
Last edited by nobbs; Dec 19, 2010 at 07:46 PM.
Just saw some pics of your car on HT. Nice to see you're on here now.
If you're referring to the bumper mounting tabs then you can cut them off, drill some holes, and then use zip ties to secure the bumper.
If you're referring to the bumper mounting tabs then you can cut them off, drill some holes, and then use zip ties to secure the bumper.
Thread Starter
|
New Member
Joined: Dec 2010
Posts: 2
From: Sydney, Australia
Hi All,
Thanks for the replies... i parted ways with my jazz a few months back and am now driving an Evo... the car has had a few changes under its new ownership... heres a pic that was taken last weekend as it stands now.
The decal is actually the logo for JDMYARD, one of the leading importers of honda parts here in Australia...
Thanks for the replies... i parted ways with my jazz a few months back and am now driving an Evo... the car has had a few changes under its new ownership... heres a pic that was taken last weekend as it stands now.
The decal is actually the logo for JDMYARD, one of the leading importers of honda parts here in Australia...