Unofficial Honda FIT Forums
I've got a few surprises left for the build...
I've got a few surprises left for the build...
0 2021/03/24 17:39:21
0 2021/03/20 07:22:48
0 2021/03/20 07:22:32
0 2021/03/20 07:22:22
0 2021/03/10 20:10:23
After cutting before paint
After cutting before paint
0 2021/03/10 20:10:08
I just measured and bought all this. I got an extra foot of silicone tube because i wasn't sure how much aluminum would extend from the 90s on these 4.5" radii. 3" pipe and filter...
I just measured and bought all this. I got an extra foot of silicone tube because i wasn't sure how much aluminum would extend from the 90s on these 4.5" radii. 3" pipe and filter...
0 2021/03/10 20:09:53
0 2021/03/10 20:09:41
Here's my intake pipes. Might install before the motor if the rzcrew intake gets here in time...
Here's my intake pipes. Might install before the motor if the rzcrew intake gets here in time...
0 2021/03/10 20:09:27
Nice packaging
Nice packaging
0 2021/03/10 20:09:13
0 2021/03/10 20:08:58
0 2021/03/10 20:08:43
0 2021/03/10 20:08:28
Just unpacked
Just unpacked
0 2021/03/10 20:08:14
I used the flex plate in a previous photo with two flywheel bolts to turn the motor to install the piston oil squirters.
I used the flex plate in a previous photo with two flywheel bolts to turn the motor to install the piston oil squirters.
0 2021/03/10 20:07:57
The ARP fasteners are stout...
The ARP fasteners are stout...
0 2021/03/10 20:07:42
I took some hard looks at the new hardware vs the OG. This thing is going to make a lot of power in the high rpms. You can probably see where GE Drilled the crank for balancing... or maybe honda did and i didn't notice?
I took some hard looks at the new hardware vs the OG. This thing is going to make a lot of power in the high rpms. You can probably see where GE Drilled the crank for balancing... or maybe honda did and i didn't notice?
0 2021/03/10 20:07:28
Decided to take the oil pump off and let them install since i have no idea on torque values
Decided to take the oil pump off and let them install since i have no idea on torque values
0 2021/03/10 20:07:13
That's how that all goes against the block, not the front cover, so i have to think in reverse...
That's how that all goes against the block, not the front cover, so i have to think in reverse...
0 2021/03/10 20:06:56
It was a pain to guess what to take to Precision who are dialing in my cam, but i know now
It was a pain to guess what to take to Precision who are dialing in my cam, but i know now
0 2021/03/10 20:06:40
Blow up that pic! Dayum!!!
Blow up that pic! Dayum!!!
0 2021/03/10 20:06:25
0 2021/03/10 20:02:34
ARP main, rod, and head studs going to clamp it down tight...
ARP main, rod, and head studs going to clamp it down tight...
0 2021/03/09 13:21:25
Traum 12.5:1 pistons with oversize valve recesses
Traum 12.5:1 pistons with oversize valve recesses
0 2021/03/09 13:21:09
0 2021/03/02 15:01:38
0 2021/02/21 14:44:29
0 2021/02/21 14:43:45
0 2021/01/24 19:18:39
0 2021/01/24 19:18:29
0 2021/01/24 19:18:19
0 2021/01/24 19:18:09
0 2021/01/24 19:17:59
0 2021/01/24 19:17:49
0 2021/01/24 19:17:39
0 2021/01/24 19:17:30
0 2021/01/20 11:33:46
0 2021/01/20 11:33:36
0 2021/01/20 11:33:27
Another of the back
Another of the back
0 2021/01/20 11:33:17
Drivers front panel
Drivers front panel
0 2021/01/20 11:33:07