Unofficial Honda FIT Forums
Tune up: plugs, cap, rotor, wires.
Tune up: plugs, cap, rotor, wires.
0 2017/03/23 17:32:12
300 watts rms 600 peak *4 channels
300 watts rms 600 peak *4 channels
0 2017/03/23 17:34:37
0 2017/03/23 17:54:49
Jeep Life, repair and rehung door. Replaced rear brakes.
Jeep Life, repair and rehung door. Replaced rear brakes.
0 2017/03/25 18:17:56
Ben was kind enough to give me a rear wiper arm and motor, so clean, prime, and paint.
Ben was kind enough to give me a rear wiper arm and motor, so clean, prime, and paint.
0 2017/03/26 16:41:45
Yeah that's a word arm, I cut and install the blades myself. I figured that with all the cars in our family this was a win win . I get refills at 28" for .60 a piece and at 2.00 to 17.00 for the assembly, what a savings.
Yeah that's a word arm, I cut and install the blades myself. I figured that with all the cars in our family this was a win win . I get refills at 28" for .60 a piece and at 2.00 to 17.00 for the assembly, what a savings.
0 2017/03/26 16:43:49
0 2017/03/28 17:36:03
0 2017/03/28 17:36:30
0 2017/03/28 17:37:14
Original cover A little ratty and faded but for 24 years old not bad.
Original cover A little ratty and faded but for 24 years old not bad.
0 2017/03/29 17:39:55
Carefully pull the cover off to make the template.
Carefully pull the cover off to make the template.
0 2017/03/29 17:41:46
Sewing the seams together.
Sewing the seams together.
0 2017/03/29 17:43:04
Test fitment.
Test fitment.
0 2017/03/29 17:44:18
Done
Done
0 2017/03/29 17:45:35
Getting missing OEM parts back on "Big Bird"
Getting missing OEM parts back on "Big Bird"
0 2017/04/01 15:14:24
0 2017/04/01 15:18:02
Adjusted fender and bumper skin to match up better
Adjusted fender and bumper skin to match up better
0 2017/04/01 19:26:39
0 2017/04/01 19:28:45
Added new fasteners and cleaned up others.
Added new fasteners and cleaned up others.
0 2017/04/01 19:29:18
Bake at 200 degrees for 30 min. to loose glue. Then be careful with a med. flat blade screwdriver gently pry catches out of the backing. There is 1 #1 Phillips screwdriver to remove where the side reflector is.
Bake at 200 degrees for 30 min. to loose glue. Then be careful with a med. flat blade screwdriver gently pry catches out of the backing. There is 1 #1 Phillips screwdriver to remove where the side reflector is.
0 2017/04/04 18:22:23
After cleaning mask it off and I used bright silver metallic.
After cleaning mask it off and I used bright silver metallic.
0 2017/04/04 18:27:36
0 2017/04/04 18:29:00
0 2017/04/04 18:29:22
I am using a black sealing mastic strip to seal it back up. Reheat @ 200 put just the housing in and when the seal is soft replace the lens and snap it back into the housing ,.... Carefully.
I am using a black sealing mastic strip to seal it back up. Reheat @ 200 put just the housing in and when the seal is soft replace the lens and snap it back into the housing ,.... Carefully.
0 2017/04/04 18:29:43
Here they are fresh out of the box. Collar is a little bit bigger than 2" . Which works out to the good as that way I could get a tight fit. There is a square cob in the light and I could not look at it when powered up. And the ring is bright white.
Here they are fresh out of the box. Collar is a little bit bigger than 2" . Which works out to the good as that way I could get a tight fit. There is a square cob in the light and I could not look at it when powered up. And the ring is bright white.
0 2017/04/06 17:51:27
Measured and made a mark center and a little bit high as I want room in-between to clean the dirt out when detailing. BTJM.
Measured and made a mark center and a little bit high as I want room in-between to clean the dirt out when detailing. BTJM.
0 2017/04/06 17:56:24
Not the best shot of them but this is the test fit. Me likey!
Not the best shot of them but this is the test fit. Me likey!
0 2017/04/06 17:59:13
Driving lights
Driving lights
0 2017/04/07 18:06:16
Hi beams H1 bulbs in plastic housings, ran a ground to the bulb. And they came on, yeah!!
Hi beams H1 bulbs in plastic housings, ran a ground to the bulb. And they came on, yeah!!
0 2017/04/07 18:08:51
Pulled the red tails out, and had a good ol time installing the renewed LS tails. Cleaned the housing area and as I dug into the hatch area .... I found lots of missing fasteners. So it was too late and I am too worn out to take her for a ride too listen to the quiet
Pulled the red tails out, and had a good ol time installing the renewed LS tails. Cleaned the housing area and as I dug into the hatch area .... I found lots of missing fasteners. So it was too late and I am too worn out to take her for a ride too listen to the quiet
0 2017/04/08 19:03:22
Under tail light where the bumper attaches to the car.
Under tail light where the bumper attaches to the car.
0 2017/04/08 19:11:26
The original color was grey metalic
The original color was grey metalic
0 2017/04/08 19:13:01
Old ps renew ds
Old ps renew ds
0 2017/04/08 19:14:56
Paint sealant and NXT wax and alot of elbow grease, lol.
Paint sealant and NXT wax and alot of elbow grease, lol.
0 2017/04/09 18:17:37
Refinished fasteners for the 3rd brake light and windows.
Refinished fasteners for the 3rd brake light and windows.
0 2017/04/09 18:19:25
0 2017/04/09 18:21:04
Removed and cleaned brake light, rear glass. Cleaned door jambs, and headliner tonight.
Removed and cleaned brake light, rear glass. Cleaned door jambs, and headliner tonight.
0 2017/04/10 17:39:38
Pulled solenoid pack and checked screen, it was fine. Touched up yellow under the hood.
Pulled solenoid pack and checked screen, it was fine. Touched up yellow under the hood.
0 2017/04/11 15:29:34
Hemi
Hemi
0 2017/04/11 15:32:11
March 1
March 1
0 2017/04/11 17:12:14