Unofficial Honda FIT Forums
Hi beams H1 bulbs in plastic housings, ran a ground to the bulb. And they came on, yeah!!
Hi beams H1 bulbs in plastic housings, ran a ground to the bulb. And they came on, yeah!!
0 2017/04/07 18:08:51
Driving lights
Driving lights
0 2017/04/07 18:06:16
Not the best shot of them but this is the test fit. Me likey!
Not the best shot of them but this is the test fit. Me likey!
0 2017/04/06 17:59:13
Measured and made a mark center and a little bit high as I want room in-between to clean the dirt out when detailing. BTJM.
Measured and made a mark center and a little bit high as I want room in-between to clean the dirt out when detailing. BTJM.
0 2017/04/06 17:56:24
Here they are fresh out of the box. Collar is a little bit bigger than 2" . Which works out to the good as that way I could get a tight fit. There is a square cob in the light and I could not look at it when powered up. And the ring is bright white.
Here they are fresh out of the box. Collar is a little bit bigger than 2" . Which works out to the good as that way I could get a tight fit. There is a square cob in the light and I could not look at it when powered up. And the ring is bright white.
0 2017/04/06 17:51:27
I am using a black sealing mastic strip to seal it back up. Reheat @ 200 put just the housing in and when the seal is soft replace the lens and snap it back into the housing ,.... Carefully.
I am using a black sealing mastic strip to seal it back up. Reheat @ 200 put just the housing in and when the seal is soft replace the lens and snap it back into the housing ,.... Carefully.
0 2017/04/04 18:29:43
0 2017/04/04 18:29:22
0 2017/04/04 18:29:00
After cleaning mask it off and I used bright silver metallic.
After cleaning mask it off and I used bright silver metallic.
0 2017/04/04 18:27:36
Bake at 200 degrees for 30 min. to loose glue. Then be careful with a med. flat blade screwdriver gently pry catches out of the backing. There is 1 #1 Phillips screwdriver to remove where the side reflector is.
Bake at 200 degrees for 30 min. to loose glue. Then be careful with a med. flat blade screwdriver gently pry catches out of the backing. There is 1 #1 Phillips screwdriver to remove where the side reflector is.
0 2017/04/04 18:22:23
Added new fasteners and cleaned up others.
Added new fasteners and cleaned up others.
0 2017/04/01 19:29:18
0 2017/04/01 19:28:45
Adjusted fender and bumper skin to match up better
Adjusted fender and bumper skin to match up better
0 2017/04/01 19:26:39
0 2017/04/01 15:18:02
Getting missing OEM parts back on "Big Bird"
Getting missing OEM parts back on "Big Bird"
0 2017/04/01 15:14:24
Done
Done
0 2017/03/29 17:45:35
Test fitment.
Test fitment.
0 2017/03/29 17:44:18
Sewing the seams together.
Sewing the seams together.
0 2017/03/29 17:43:04
Carefully pull the cover off to make the template.
Carefully pull the cover off to make the template.
0 2017/03/29 17:41:46
Original cover A little ratty and faded but for 24 years old not bad.
Original cover A little ratty and faded but for 24 years old not bad.
0 2017/03/29 17:39:55
0 2017/03/28 17:37:14
0 2017/03/28 17:36:30
0 2017/03/28 17:36:03
Yeah that's a word arm, I cut and install the blades myself. I figured that with all the cars in our family this was a win win . I get refills at 28" for .60 a piece and at 2.00 to 17.00 for the assembly, what a savings.
Yeah that's a word arm, I cut and install the blades myself. I figured that with all the cars in our family this was a win win . I get refills at 28" for .60 a piece and at 2.00 to 17.00 for the assembly, what a savings.
0 2017/03/26 16:43:49
Ben was kind enough to give me a rear wiper arm and motor, so clean, prime, and paint.
Ben was kind enough to give me a rear wiper arm and motor, so clean, prime, and paint.
0 2017/03/26 16:41:45
Jeep Life, repair and rehung door. Replaced rear brakes.
Jeep Life, repair and rehung door. Replaced rear brakes.
0 2017/03/25 18:17:56
0 2017/03/23 17:54:49
300 watts rms 600 peak *4 channels
300 watts rms 600 peak *4 channels
0 2017/03/23 17:34:37
Tune up: plugs, cap, rotor, wires.
Tune up: plugs, cap, rotor, wires.
0 2017/03/23 17:32:12
0 2017/03/23 12:32:39
What a great night! And yep the fronts scrape ain't it great! 🤔
What a great night! And yep the fronts scrape ain't it great! 🤔
0 2017/03/22 18:22:48
0 2017/03/22 18:22:28
Take a last look at the 117k struts, coilovers with top hats are replacing them soon!
Take a last look at the 117k struts, coilovers with top hats are replacing them soon!
0 2017/03/22 18:20:09
Of course I can't install the flaps without cleaning, ha ha.
Of course I can't install the flaps without cleaning, ha ha.
0 2017/03/22 18:18:24
These came, so that led to this.....
These came, so that led to this.....
0 2017/03/22 17:13:03
Tied the front bumper into the frame. And the inter fenders reattached all round. Then.....
Tied the front bumper into the frame. And the inter fenders reattached all round. Then.....
0 2017/03/22 17:09:09
Ahhh relaxn time !
Ahhh relaxn time !
0 2017/03/21 17:19:31
B4 no way Jose
B4 no way Jose
0 2017/03/21 14:17:46
Mucho better senyor cc
Mucho better senyor cc
0 2017/03/21 14:15:04
Truck bed liner resists chips
Truck bed liner resists chips
0 2017/03/21 14:12:27