1st Generation (GD 01-08) The one that started it all! Generation specific talk and questions here!

Check engine light on, no code from OBD2 scan, now what?

Thread Tools
 
Search this Thread
 
  #1  
Old 08-20-2015, 02:06 AM
Rob22315's Avatar
Member
5 Year Member
Thread Starter
Join Date: Mar 2008
Location: Wash DC Metro
Posts: 587
Check engine light on, no code from OBD2 scan, now what?

I used Torque to check the codes and do a full readout on the engine parameters. No codes but a few of the parameters were out of whack. Any suggestions for where to start?

Car seems to run fine for a car with 103k miles on it. I did the valve regap two weeks ago but not much else recently.
 
  #2  
Old 08-20-2015, 09:52 AM
kenchan's Avatar
Official Fit Blogger of FitFreak
5 Year Member
iTrader: (4)
Join Date: Dec 2007
Location: OG Club
Posts: 20,289
can u clear it? see if it comes back.
 
  #3  
Old 08-20-2015, 11:06 AM
Rob22315's Avatar
Member
5 Year Member
Thread Starter
Join Date: Mar 2008
Location: Wash DC Metro
Posts: 587
I did a code clear but the light stayed on. Any chance this si an indication that it's time to change the coolant?
 
  #4  
Old 08-20-2015, 11:33 AM
kenchan's Avatar
Official Fit Blogger of FitFreak
5 Year Member
iTrader: (4)
Join Date: Dec 2007
Location: OG Club
Posts: 20,289
I doubt there is an ses for coolant change interval.
 
  #5  
Old 08-20-2015, 12:52 PM
Rob22315's Avatar
Member
5 Year Member
Thread Starter
Join Date: Mar 2008
Location: Wash DC Metro
Posts: 587
Originally Posted by kenchan
I doubt there is an ses for coolant change interval.
The manual says there is but it might be a B4 rather than the engine light.v it's supposed to come on around 120k miles
 
  #6  
Old 08-28-2015, 09:35 PM
Rob22315's Avatar
Member
5 Year Member
Thread Starter
Join Date: Mar 2008
Location: Wash DC Metro
Posts: 587
The light went out. I'm guessing one of our drivers didn't get the gas cap on all the way.
 
  #7  
Old 08-30-2015, 08:29 PM
Carbuff2's Avatar
Member
5 Year Member
Join Date: Mar 2007
Location: Second house on the left
Posts: 1,704
Once I forgot to reconnect the IAT sensor on my CR-V after cleaning the throttle body. I couldn't turn off the CEL. (But the code went away) It finally extinguished on it's own after a number of drive cycles.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
PhilRai
2nd Generation (GE 08-13)
3
12-06-2016 07:12 PM
payluder
3rd Generation (2015+)
6
06-28-2016 01:06 PM
kitenok
2nd Generation GE8 Specific DIY: Repair & Maintenance Sub-Forum
12
12-10-2015 07:28 PM
SevereService
2nd Generation GE8 Specific DIY: Repair & Maintenance Sub-Forum
4
09-07-2014 03:14 PM
bjvalencia
Fit DIY: Repair & Maintenance
14
10-11-2011 03:16 AM



Quick Reply: Check engine light on, no code from OBD2 scan, now what?



All times are GMT -4. The time now is 08:57 AM.