Honda Fit 09 Short ram intake
#1
Honda Fit 09 Short ram intake
I'm sure there's many place with this discution but I couldn't find anything...
What are the Short Ram Intake choices I can put in my Fit 09?
I've seen many like AEM, Injen, Fujita, K&N, etc for the 07-08... But nothing excepts crap-with-names-I-don't-know from eBay.
Could you help me please =)!
What are the Short Ram Intake choices I can put in my Fit 09?
I've seen many like AEM, Injen, Fujita, K&N, etc for the 07-08... But nothing excepts crap-with-names-I-don't-know from eBay.
Could you help me please =)!
#2
Member
iTrader: (2)
Join Date: Mar 2007
Location: Winthrop Harbor Illinois/ Presque Isle Wisconsin
Posts: 1,251
I'm sure there's many place with this discution but I couldn't find anything...
What are the Short Ram Intake choices I can put in my Fit 09?
I've seen many like AEM, Injen, Fujita, K&N, etc for the 07-08... But nothing excepts crap-with-names-I-don't-know from eBay.
Could you help me please =)!
What are the Short Ram Intake choices I can put in my Fit 09?
I've seen many like AEM, Injen, Fujita, K&N, etc for the 07-08... But nothing excepts crap-with-names-I-don't-know from eBay.
Could you help me please =)!
The short ram might be especially effective on the 09 because some cooler air is ducted to that area.
The one that 10's of people have on this site is the PRM, They are a vendor here and can be found in the vendor section. Very tuned into our Fit community, great quality and great to work with.
Other than that, one guy I think has the K&N (the 07-08 version I believe didnt make any power, the 09 might be better).
One guy might have the Last Station, and Maybe nobody has a Fujita yet.
So we are mainly PRM here and I believe every review has been a good one (also they are in Canada). Hope that helps
Last edited by Tork; 07-18-2009 at 12:31 PM.
#8
Member
iTrader: (2)
Join Date: Mar 2007
Location: Winthrop Harbor Illinois/ Presque Isle Wisconsin
Posts: 1,251
Honestly, the 2 all in all are just short rams, one is not going to be very different than the other, especially on the low RPM side. It is difficult too, one guys dyno shows 1 at 2.5 or whatever and the other does not, I mean if you know anything about dyno runs, it is a wash. The thing is, get what you want, that will be the best one for you
I did go with the PRM CAI, as those numbers were +6HP and +4 torque, down side is wont fit AT, and going thru deep water is out of the question
#11
I don't think the old PRM is a two piece. The new intake PRM is currently selling is only a short ram. Same design as the K&N except with no heat shield and a different filter.
#19
here is the trust one that i am thinking of getting:
http://www.trust-power.com/php/update/new_products.php?id=13205200905070910112551023
can someone confirm if this will fit on the usdm fit with no issues?
also here are the strut bars from trust as well
http://www.trust-power.com/php/update/new_products.php?id=13222200905290610114053029
http://www.trust-power.com/php/update/new_products.php?id=13223200905290610114053030
http://www.trust-power.com/php/update/new_products.php?id=13205200905070910112551023
can someone confirm if this will fit on the usdm fit with no issues?
also here are the strut bars from trust as well
http://www.trust-power.com/php/update/new_products.php?id=13222200905290610114053029
http://www.trust-power.com/php/update/new_products.php?id=13223200905290610114053030