After 7 years of owning the fit I am just now starting to mod it!
#4
08-16-2016, 03:31 AM
You will love that Bilstein 
I use to have it on my car.
Just don't lowered the front coil over too much because it would run out of suspension travel on bumpy road and hurt handling.
The rear one, you can lowered it to the max.
oh, and get SPC camber bolt to get about 1.5 to minus 2 camber up front.
you need 4 pieces of SPC camber bolt (bought 2 set, they come in pairs).
I use to have it on my car.
Just don't lowered the front coil over too much because it would run out of suspension travel on bumpy road and hurt handling.
The rear one, you can lowered it to the max.
oh, and get SPC camber bolt to get about 1.5 to minus 2 camber up front.
you need 4 pieces of SPC camber bolt (bought 2 set, they come in pairs).
#5
08-16-2016, 06:42 AM
Raleigh, I actually lived in Wilmington NC for 4 years, until I got a new job here in Raleigh, I used to work at PPD! Still got my beach cruiser as well: http://imgur.com/a/sh2EQ we could squad up!
Thanks for the tip. I was wondering about those camber bolts! But I couldn't find the information if I needed them with the bilsteins or not. So I need them even if iam lowering a little bit?
You will love that Bilstein
I use to have it on my car.
Just don't lowered the front coil over too much because it would run out of suspension travel on bumpy road and hurt handling.
The rear one, you can lowered it to the max.
oh, and get SPC camber bolt to get about 1.5 to minus 2 camber up front.
you need 4 pieces of SPC camber bolt (bought 2 set, they come in pairs).
I use to have it on my car.
Just don't lowered the front coil over too much because it would run out of suspension travel on bumpy road and hurt handling.
The rear one, you can lowered it to the max.
oh, and get SPC camber bolt to get about 1.5 to minus 2 camber up front.
you need 4 pieces of SPC camber bolt (bought 2 set, they come in pairs).
Last edited by Vash; 08-16-2016 at 07:26 AM.
#8
08-17-2016, 06:17 PM
Raleigh, I actually lived in Wilmington NC for 4 years, until I got a new job here in Raleigh, I used to work at PPD! Still got my beach cruiser as well: Sky's out Thighs out! - Album on Imgur we could squad up!
Thanks for the tip. I was wondering about those camber bolts! But I couldn't find the information if I needed them with the bilsteins or not. So I need them even if iam lowering a little bit?
Thanks for the tip. I was wondering about those camber bolts! But I couldn't find the information if I needed them with the bilsteins or not. So I need them even if iam lowering a little bit?
Last edited by Desmond Lamar MacRae; 08-17-2016 at 06:23 PM.
#10
08-19-2016, 11:18 AM
Hehee same here before I bought my fit. Had a mustang that was insainly modded with just way too much boost to be enjoyable. This fit has been the best decision of my life
Thread
Thread Starter
Forum
Replies
Last Post
FitMinister
2nd Generation GE8 Specific Suspension & Brakes Sub-Forum
6
02-12-2017 01:11 PM
ciref8
2nd Generation GE8 Specific Suspension & Brakes Sub-Forum
10
10-17-2014 12:31 AM
JCrimson
Fit Suspension & Brake Modifications
6
01-30-2011 03:20 PM
