thats what she said O_o

haha anywho looks good

 

I wanted the most "unique" and uncommon color and I got it!

As far as the "Go lower" comments are concerned, it's on the way. I hope to be tucking tire before too long! It all comes down to money and time so we shall see.

Here's some more pics:






Still not caught up yet!

More still on the way...

 

more pics:

Back to stock temporarily:

Next to a stock one at the local walmart:


Was going to run at Carolina Motorsports park, but got rained out:

Random pics out driving:

Still not caught up yet!

 

What are you dropped on?

 

In all these photos so far I'm on Dropzone springs off ebay for the GD3 chassis fit.

And yes I know mine is a GE8. And yes, GD3 springs work fine. There is a slight difference in the rear though which makes it sit abit higher than I liked.

So now I'm on 2.5" circle track style racing springs, 150 lb/in, cut to length so the rear isn't higher than the front.

 

So far I have run:
16x6 et 48 mini cooper S-winders with 185/55-16 Bridgestone factory tires
15x6.5 et40 Drag DR31 w/ 205/50-15 Falken Azenis RT615
14x6 et20 Momo mesh wheels w/ 185/60-14 kumho 732
17x7.5 et 32 Falken Hanabi w/ 205/40-17 Falken ZE 512 and 195/40-17 yokohama s-drive
17x8 et38f et35r Axis Apex w/ 205/40-17 falken ze512 and falken ze912
15x7 et40 Drag DR44 w/ 205/50-15 kumho ast

 

More pics!
Finally got the height about where it should be on the rear:




Out in the wild:


Outside a department store:


Beside a Wal-Mart:

Nearly caught up!

 

It would look way better if you got coilovers to close the wheel gap.

 

On 15x7 et40 Drag DR44s with 195/50-15 Kumho Ecsta AST tires, and tinted taillights:







Still got more pics of updates to upload...

 

So I went back to the 17's for a while...



DSCF2044.jpg?t=1313458390

 

Put some orange chrome rim stripes on...

 

Axis 17s look the best, but imo lose the orange wheel tape. It also appears your a wheel whore much like myself.

 

I plan to do either coilovers or air ride at some point. Just gotta save up for it.

I really miss my Axis wheels. They've been gone for a while now. And man, for some reason I just can't get over rimstripes. I just love them. And yes I'm a bit of a wheel whore. Right now I only have two cars, and yet I have 6 sets of wheels currently.

More pics! Trying to get caught up.
View from my window last winter when it snowed like crazy:





And then back on the stockies after I sold the 17's:




And a teaser of my next wheels...

 

New wheels! Pics from March or somewhere thereabouts.
17x7.5 et42 Drag Dr34 with 205/40-17 tires, and 8mm spacer with extended studs in the rear.

 

Looks great! When you had the mini Cooper rims, what lugs did you have on there?
And with you current set up, where did you get the spacers and the extended studs?

Keep up with good work! And get some coils! Check out the group buy on the buddy club n++.

 

Got the extended studs off eBay, they are for a '92-'95 Honda civic. However, the part # info says they fit pretty much every 12x1.50 thread pitch Honda from the last 20 years, so I wasn't concerned with them working on the fit. Sure enough, they work great. The spacers are just cheap slip on ones with a hub centering ring in the middle so they center on the hub. I ran open end 12x1.50 cone seat lug nuts from discount tire on the mini cooper wheels.

 

all the Fits posted in this thread are SCREAMING for a drop!!! do u guys not drop em?

 

There is only one Fit in this thread....

And it is lowered on some GD3 Dropzone front springs, and 12" 125lb/in circle track springs in the rear. Not enough $$$ for coilovers or air ride yet...

 

I think the Falken's looked best.

 

I did like those wheels...