Unofficial Honda FIT Forums
Part number is clear enough
Part number is clear enough
0 2020/11/19 06:41:06
0 2020/08/18 07:46:04
Short in the flasher will call for a new cluster board
Short in the flasher will call for a new cluster board
0 2020/04/06 10:43:39
Very fine irregular line at the fold; had same on the tie rod end boots.
Very fine irregular line at the fold; had same on the tie rod end boots.
0 2020/03/04 10:22:16
OEM brake rotor with pad after 15,000 miles since replacement
OEM brake rotor with pad after 15,000 miles since replacement
0 2020/03/02 07:26:00
Ball joint boot is starting to crack
Ball joint boot is starting to crack
0 2020/03/02 07:25:01
Bent arm??
Bent arm??
0 2020/03/02 06:58:18
0 2020/02/21 13:49:53
ready for assembly
ready for assembly
0 2020/02/19 07:56:47
Tools
Tools
0 2020/02/19 07:56:18
brake shoe spreader, 30mm wide
brake shoe spreader, 30mm wide
0 2020/02/19 07:55:40
This ugly film is easy to wash out
This ugly film is easy to wash out
0 2020/02/19 07:54:50
components before cleaning
components before cleaning
0 2020/02/19 07:54:21
0 2020/01/02 10:23:24
Better view
Better view
0 2019/10/24 06:59:44
0 2019/10/21 14:53:08
0 2019/10/21 14:53:06
0 2019/10/21 14:53:04
This kind of damage is cosmetic and very easy to fix
This kind of damage is cosmetic and very easy to fix
0 2019/10/21 14:45:20
It took about 25 minutes to remove both of them (used hammer)
It took about 25 minutes to remove both of them (used hammer)
0 2019/10/21 14:45:19
0 2019/10/10 07:04:49
Slightly off topic, shows some details
Slightly off topic, shows some details
0 2019/09/30 08:48:27
Coil and sleeve close up
Coil and sleeve close up
0 2019/09/30 08:47:45
When this grease dries, it takes a bit longer to retract, causing a cold start noise
When this grease dries, it takes a bit longer to retract, causing a cold start noise
0 2019/09/30 08:46:21
The solenoid plunger , covered with sticky layer of grease is going into the brass sleeve
The solenoid plunger , covered with sticky layer of grease is going into the brass sleeve
0 2019/09/30 08:44:48
0 2019/09/11 12:49:11
0 2019/09/10 08:37:21
Adjusting bolt and set bolt (12mm); I match marked them for reference before disassembly to assure accurate belt tension adjustment
Adjusting bolt and set bolt (12mm); I match marked them for reference before disassembly to assure accurate belt tension adjustment
0 2019/09/06 08:25:36
One more view
One more view
0 2019/09/06 08:20:12
The roller is a bit tricky to get in
The roller is a bit tricky to get in
0 2019/09/06 08:20:11
12 mm socket on the alternator pivot bolt
12 mm socket on the alternator pivot bolt
0 2019/09/06 08:20:10
If alternator pivot bolt is not too tight , itis possible to break it loose from under the car
If alternator pivot bolt is not too tight , itis possible to break it loose from under the car
0 2019/09/06 08:20:09
0 2019/09/06 08:20:07
It is also possible to reach this bolt from the top with swivel socket (u-joint may slip off)
It is also possible to reach this bolt from the top with swivel socket (u-joint may slip off)
0 2019/09/06 08:20:06
0 2019/09/06 08:19:26
Dipstick tube removal tool
Dipstick tube removal tool
0 2019/08/19 14:13:44
Made in China burned up coil (was not able to check spark plug tightness due to the lack of socket)
Made in China burned up coil (was not able to check spark plug tightness due to the lack of socket)
0 2019/08/19 13:52:42
Upside down mounted front strut mount; car has aftermarket front struts of unknown brand
Upside down mounted front strut mount; car has aftermarket front struts of unknown brand
0 2019/08/19 13:51:38
Gabriel rear shock with scrub mark
Gabriel rear shock with scrub mark
0 2019/08/19 13:50:53
Another car around 70,000 miles
Another car around 70,000 miles
0 2019/08/12 07:04:46