Unofficial Honda FIT Forums
0 2022/08/09 04:56:57
also, here's a baby toad we found on our back patio. Life's kinda suckin' right now, but this makes up for a lot.
also, here's a baby toad we found on our back patio. Life's kinda suckin' right now, but this makes up for a lot.
0 2022/07/21 20:09:22
It's a tight squeeze!
It's a tight squeeze!
0 2022/07/10 09:43:41
Unbolt and slide to *your* right to unhook. Will have to hold this plastic wire routing bracket out of the way for access/visibility
Unbolt and slide to *your* right to unhook. Will have to hold this plastic wire routing bracket out of the way for access/visibility
0 2022/07/10 09:43:36
0 2022/07/10 09:43:31
0 2022/07/10 09:42:16
0 2022/06/30 07:26:13
0 2022/06/25 20:27:18
0 2022/05/10 13:22:25
Unbolt these two bolts and move this plastic whatsit off to your right. Kinda hidden in there. This doesn't disconnect anything, so you can run the car and then pinch the hose there..
Unbolt these two bolts and move this plastic whatsit off to your right. Kinda hidden in there. This doesn't disconnect anything, so you can run the car and then pinch the hose there..
0 2022/04/30 07:47:52
0 2022/04/30 07:47:33
0 2022/04/30 07:47:20
0 2022/04/26 06:36:06
Not a plug, but an example.
Not a plug, but an example.
0 2022/04/23 14:12:12
Started the new bearing by placing the old one on top of it and going around with a standard 2lb claw hammer knocking it a little at a time. Finished using 1-1/16 socket and a 49oz dead blow rubber mallet. If I kept using the old bearing it might've gotten stuck in the pulley with the new one. Though the image shows the drive side of the socket being up, i flipped it for hammering, placing the drive side against the bearing. Seemed flatter/safer
Started the new bearing by placing the old one on top of it and going around with a standard 2lb claw hammer knocking it a little at a time. Finished using 1-1/16 socket and a 49oz dead blow rubber mallet. If I kept using the old bearing it might've gotten stuck in the pulley with the new one. Though the image shows the drive side of the socket being up, i flipped it for hammering, placing the drive side against the bearing. Seemed flatter/safer
0 2022/03/17 19:02:14
Here's a side-by side with the new bearing installed, verifying fitment. Numbers are visible. Timken 6203-2RS fits and operates within the desired RPM range, nod to OP for figuring out what that is.
Here's a side-by side with the new bearing installed, verifying fitment. Numbers are visible. Timken 6203-2RS fits and operates within the desired RPM range, nod to OP for figuring out what that is.
0 2022/03/17 19:00:08
Finished knocking it out on this old inner race from a ford wheel bearing.
Finished knocking it out on this old inner race from a ford wheel bearing.
0 2022/03/17 18:59:06
Got flush with the pulley as mentioned in above post
Got flush with the pulley as mentioned in above post
0 2022/03/17 18:58:13
Starting to knock out old bearing
Starting to knock out old bearing
0 2022/03/17 18:57:43
0 2022/03/17 18:57:03
When you select a specific hitch you'll see this option
When you select a specific hitch you'll see this option
0 2022/02/22 08:30:02
0 2022/02/13 07:01:11
0 2022/02/13 06:58:41
0 2022/02/13 06:58:31
0 2022/01/31 10:43:05
69-1017TTK
69-1017TTK
0 2022/01/24 07:21:08
These are the original plugs
These are the original plugs
0 2022/01/20 06:54:52
0 2022/01/17 17:30:12
0 2022/01/17 17:29:46
2015 (3rd gen) OEM plugs
2015 (3rd gen) OEM plugs
0 2022/01/17 17:27:34
07 (first gen) OEM plugs
07 (first gen) OEM plugs
0 2022/01/17 17:27:04
Our OEM plugs
Our OEM plugs
0 2022/01/17 17:26:14
Fit the door handle in, slide it to the left to line up the screw hole, screw it in AND YOU'RE DONE
Fit the door handle in, slide it to the left to line up the screw hole, screw it in AND YOU'RE DONE
0 2022/01/10 14:58:13
Fascia panel (left side has a tab that hooks in first)
Fascia panel (left side has a tab that hooks in first)
0 2022/01/10 14:57:29
Screw!
Screw!
0 2022/01/10 14:56:48
Press the panel on
Press the panel on
0 2022/01/10 14:55:06
An image of one of the clips used to fasten the door panel. They're great! No breakage.
An image of one of the clips used to fasten the door panel. They're great! No breakage.
0 2022/01/10 14:51:40
Hold up the door panel and fit the door handle and the control panel connector through, then hang the top edge of the door panel in the window sill up against the glass.
Hold up the door panel and fit the door handle and the control panel connector through, then hang the top edge of the door panel in the window sill up against the glass.
0 2022/01/10 14:48:19
Reinstall speaker
Reinstall speaker
0 2022/01/10 14:45:32
Barrier in place, clip the two legs of the harness back into the door.
Barrier in place, clip the two legs of the harness back into the door.
0 2022/01/10 14:43:28