Sugarphreak 2.0 - Kickoff
Thread Starter
|
Push My Button
Joined: May 2007
Posts: 4,997
From: Calgary, Alberta
Catcams has upgraded cams, valve springs, and retainers for the Fit.
CATCAMS Introduction page: the pearly gates to engine power!
EDIT: WTF is AJR removing timing from your car on an N/A setup. That makes no sense unless there was something wrong to begin with.
CATCAMS Introduction page: the pearly gates to engine power!
EDIT: WTF is AJR removing timing from your car on an N/A setup. That makes no sense unless there was something wrong to begin with.
They added a lot of fuel, and wherever they subtracted a touch of timing at a ration of about 5:-1 (F/T)
Wow.... cams & springs; I think I have new new project
Thread Starter
|
Push My Button
Joined: May 2007
Posts: 4,997
From: Calgary, Alberta
I am just in the process of setting up the tuning session right now with the Dyno shop
Last edited by Sugarphreak; May 5, 2009 at 12:46 PM.
nice choice 15's are perfect. for our car 15 looks perfect on our cars. plus i really like how 15's feel on our car. i had 16's and switch to 15's. i notice it was much better right away
Thread Starter
|
Push My Button
Joined: May 2007
Posts: 4,997
From: Calgary, Alberta
The base data look something like this for a totally stock Fit on the same machine: This will be my baseline data to compare against as I plan to use the same machine in close to the same temps.
Dynamometer; Mustang Dyno
NOTE: This machine typically reads a bit lower than a dynoJet, much lower than a dynopack.
Approx Elevation: 3000ft above sea level
This will play a factor on the max power output, keep that in mind
Temp: 9 Degrees ambient
Max HP: 86.7whp @ 5800RPM
Max Torque: 83.9whp @ 4900RPM
I did do a dyno before; you can do a search for the thread; however I believe the results were comprimised with some unforeseen factors coming into play.
Dynamometer; Mustang Dyno
NOTE: This machine typically reads a bit lower than a dynoJet, much lower than a dynopack.
Approx Elevation: 3000ft above sea level
This will play a factor on the max power output, keep that in mind
Temp: 9 Degrees ambient
Max HP: 86.7whp @ 5800RPM
Max Torque: 83.9whp @ 4900RPM
I did do a dyno before; you can do a search for the thread; however I believe the results were comprimised with some unforeseen factors coming into play.
Last edited by Sugarphreak; May 6, 2009 at 02:08 PM.
that sucks. i was looking to see some dyno results today
Subscribing, wanna see what your dyno shows. For semi-relevant refrerence, here's a link to RichXKU's bone stock '07 dyno pull.
Thread Starter
|
Push My Button
Joined: May 2007
Posts: 4,997
From: Calgary, Alberta
After 2 weeks of the cold shoulder I have pretty much given up on that shop. 
I am in contact with another shop setting up an appointment now, more details in a bit.
Big appologies on the delays, this shouldn't be taking so long.
I got a nice pic of the manifold & wheels in one shot at a meet recently.
I am in contact with another shop setting up an appointment now, more details in a bit.
Big appologies on the delays, this shouldn't be taking so long.
I got a nice pic of the manifold & wheels in one shot at a meet recently.
Last edited by Sugarphreak; Jun 2, 2009 at 03:16 PM.
Thread Starter
|
Push My Button
Joined: May 2007
Posts: 4,997
From: Calgary, Alberta
....here have an extra 40K on me
I am waiting on the second guy now
Do you have one of these yet
I'm liking it even the odd stares by the unknowing
check this link out if you like.https://www.fitfreak.net/forums/gaug...-interest.html
Last edited by zonianjohn; Jun 12, 2009 at 04:35 AM.