Built from my old AEM CAI that used to be on my 2001 civic ex. Used a dryflow filter and painted it black. Its a little loud for me, but the hp and mpg is worth it. Thanks SID for the idea!
Built from my old AEM CAI that used to be on my 2001 civic ex. Used a dryflow filter and painted it black. Its a little loud for me, but the hp and mpg is worth it. Thanks SID for the idea!
Ok quick question now that we have these intakes in, how do we clean the engine? Before I used to just take it down to the car wash put some degreaser and rinse, but I know we shouldn't get this filter wet, should I wrap a towel or put plastic over it? Any suggestions?
If the engine isn't too hot, you can cover the filter with a plastic baggie secured with a rubber band or something like that. You really shouldn't hose down a hot engine, but if you have to for some reason, covering the filter with a towel will work OK if you don't saturate it with water. The filter getting a little wet really isn't going to cause any problem anyway. Some folks remove carbon from their top end by purposely feeding some water down the intake.
If you really want to keep it dry, just remove it (only takes about 10 seconds). You could cover the intake tube if you want, but they usually point down to some degree so water isn't going to defeat gravity unless you stick the hose end into the tube.
ez
__________________ Hypermiling? I budget gas under ENTERTAINMENT
Ok I am not sure what happened, but from yesterday to today I have noticed a big difference on the sound of the engine. The response seems to be the same but its a hell of alot quieter, Anyone have any ideas as to why?
__________________ San Antonio, TX
2008 Tidewater Blue Fit Sport
SSR Intake
PIAA Xtreme White Plus H4
Under dash cathodes
35% front tint, 5% all other
Is everything nice and tight and bolted down. Maybe the filter came loose or something else came loose. I am not sure. Maybe your filter got really dirty really fast.
Is everything nice and tight and bolted down. Maybe the filter came loose or something else came loose. I am not sure. Maybe your filter got really dirty really fast.
Well when I got home, I tightened everything down as a few bolts were loose but the result was still the same, like I said the engine seems to be running fine, but I did notice the suction is way less when I rev than before. Maybe I should just take it off and inspect everything for cracks (since the pipes are plastic)
__________________ San Antonio, TX
2008 Tidewater Blue Fit Sport
SSR Intake
PIAA Xtreme White Plus H4
Under dash cathodes
35% front tint, 5% all other
That is not a bad idea you could have cracked one of those plastic pipes somehow. It could have came with a defect or something.
Another thing is you could possibly just be getting used to the noise. When I first put the intake in my car I thought it was too loud and now I honestly don't hear it unless I turn the car on and don't let it warm up then just stomp on it I hear that pop from it sucking in air really fast.
Yea everything seems good, I noticed though after I tightened everything down the engine doesnt shake as much on idle, that was an annoying little problem I was having after removing the stock air box, it also seems the throttle is a bit tighter, so maybe it's for the best. I can still hear the engine WOT so thats all that really matters right?
__________________ San Antonio, TX
2008 Tidewater Blue Fit Sport
SSR Intake
PIAA Xtreme White Plus H4
Under dash cathodes
35% front tint, 5% all other
Ok, thanks for the reply. It's a little tight in there the way it is, I think I'll be doing the 90 + 45 degree setup, because that battery is in the way, even though I pushed it all the way back. My only concern with the IAT now is how little slack there is for the cable, but I guess the OEM setup wasn't much better.
If all else fails, I'll back to OEM until I can figure out how to do it right.
I think to fix worse case scenario you would be able to get another pipe and drill the hole closer to the one side that would get you closer to where the cable is coming from and have more slack.
I can't get the IAT sensor in at a perfect 90 degree angle with the elbow, will that cause me problems?
I had the same problem that the IAT was going in at an angle as well, and the one thing i did notice is that the engine seemed less responsive, perhaps cause it wasnt sitting straight it was leaking air so there wasnt much suction. Once I moved some things around and got it as close as possible this solved the problem, so keep an eye out for that.
__________________ San Antonio, TX
2008 Tidewater Blue Fit Sport
SSR Intake
PIAA Xtreme White Plus H4
Under dash cathodes
35% front tint, 5% all other
I had the same problem that the IAT was going in at an angle as well, and the one thing i did notice is that the engine seemed less responsive, perhaps cause it wasnt sitting straight it was leaking air so there wasnt much suction. Once I moved some things around and got it as close as possible this solved the problem, so keep an eye out for that.
I don't know why I am having so many problems, but the battery is being a huge problem for me. I presses on the filter in a way that caused it to fall off twice already. : ( poor fit. I just bought a 45 degree bend to move it in front of th battery. Anyone else had this problem?
I don't know why I am having so many problems, but the battery is being a huge problem for me. I presses on the filter in a way that caused it to fall off twice already. : ( poor fit. I just bought a 45 degree bend to move it in front of th battery. Anyone else had this problem?
Most people have either used a 90 and 45 bend or a 90 and 90 bend (which is what i used) to clear the battery. You will also get a better sound and slightly cooler temps. Now as far as the battery goes; loosen the nut that is holding it down enough to where you can slide the battery all the way to the right, then retighten it should give you enough clearence.
__________________ San Antonio, TX
2008 Tidewater Blue Fit Sport
SSR Intake
PIAA Xtreme White Plus H4
Under dash cathodes
35% front tint, 5% all other
So has anyone found a good way to mount these intakes so they don't vibrate and lower the possibility of it falling off while driving? I can hear the filter rattling a bit when it's under load sometimes. I want to keep it from vibrating against the radiator hose and battery bracket rod (I put a little plastic shield between the hose and the filter to remedy this for now). Tried buying the official intake mounting brackets from Spectre but they didn't work.
.
San Antonio, TX
Linear Mode
