Fit Engine Modifications, Motor Swaps, ECU TuningReference Library for Engine Modifications, Swaps and Tuning
Welcome to Fit Freak!
Welcome to Fit Freak,
You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join our community today!
Are you worried that there is going to be contact when the motor's running and vibrating?
YES! But Brian from Hasport said that the differential comes extremely close so I see what he means now! The only thing for the future would be urethane mounts! Stop engine movement. Hasport is developing them as we speak I hope....
Wave, no prob. You are protecting NYC and doing a fine job! I don't think that it will be done by the end of the week, I don't think that I'm gonna find any time to work on it really... We'll see!
I had a few minutes to work on the fit today, and so I installed the A/C compressor, the midshaft and Axles and MT fluid, and the Starter/battery cable. I also adjusted the shifter cables since they were binding a bit before and now the switch like butter!
Stay tuned, I hope to start this thing up by the weekend!
I had a few minutes to work on the fit today, and so I installed the A/C compressor, the midshaft and Axles and MT fluid, and the Starter/battery cable. I also adjusted the shifter cables since they were binding a bit before and now the switch like butter!
Stay tuned, I hope to start this thing up by the weekend!
can you get a shot of the A/C pulley? Does it get dangerously close to the frame too?
I had a K swap in an EK and the 1-2 shift was kinda sloppy when i did hard shifts at WOT...if you still remember this question when your car is running, can you test to see if you have that problem also?
It's pretty much all back together. I need to top off fluids, get the header and install it, fabricate an intake, and just check everything over once again!
The good news is it fired right up! Check out the video!
MAD PROPS. I can't wait to see some track slips(promise?). Should clear a whole lot up. Hope the header fits nicley.
FIRST GARAGE K20 HONDA FIT SWAP FTMFW!!!!
hollllllllly mother of Honda, Batman! good job! can't wait till she's complete! are you going to make any in motion videos? I"d like to see how she runs from the cockpit view
hollllllllly mother of Honda, Batman! good job! can't wait till she's complete! are you going to make any in motion videos? I"d like to see how she runs from the cockpit view
In a couple of weeks, I should have her all perfected and done. Yes I will have an in car motion video.
As for the dashboard and stuff, the check engine light is on and flashing! I have to look into that. There is no header nor o2 sensor hooked up b/c of no header, so I'm hoping it's that. I need to borrow my buddy's scanner to look futher. But hey it started!!!
In a couple of weeks, I should have her all perfected and done. Yes I will have an in car motion video.
As for the dashboard and stuff, the check engine light is on and flashing! I have to look into that. There is no header nor o2 sensor hooked up b/c of no header, so I'm hoping it's that. I need to borrow my buddy's scanner to look futher. But hey it started!!!
this is awsome dude... I suprised your not a member of b20vtec.com?? alot of long island guys are there..
In a couple of weeks, I should have her all perfected and done. Yes I will have an in car motion video.
As for the dashboard and stuff, the check engine light is on and flashing! I have to look into that. There is no header nor o2 sensor hooked up b/c of no header, so I'm hoping it's that. I need to borrow my buddy's scanner to look futher. But hey it started!!!
You can literally thank the President of Iran...
Dope
Linear Mode
